Featured Post

The TKTalkie v4 - Press 6 for the Imperial March

Upgrading - the Path from v3.15 to v4.0 (Note: I had started this draft last year but never finished it, due to personal issues and cuttin...

Showing posts with label Detonator. Show all posts
Showing posts with label Detonator. Show all posts

Saturday, April 9, 2016

Final Touches Pt 1 - Let's Touch ALL THE PIECES

As I get into the final stretch of this build before submitting for the 501st as IEB (Tier 2), I need to correct the issues I found during my last fitting.


First, I started with the rivets on the left side of the armor. I scuffed up the heads with 350 grit sandpaper, being careful not to scuff the armor, and then painted them gloss white per the CRL.

Next I wanted to tackle the extra Chicago screws in the belt that are not in the Stunt CRL but have been installed by ANOVOS. Instead of removing them and covering up the holes, I doubled down and not only kept them, but added washers to the upper two. The reason behind this was that I've already seen the two remaining screws tear through a few ANOVOS belts, so I wanted to keep all the screws to give the belt extra strength - not only that, but reinforce the upper two screws, as I was going to cover them up with iron-on patchwork.

My main issue is that the patch I had was too white. So to rectify this, I made a tea bath to stain the patch off white; then, I soaked the patch in the tea bath for less than a minute.


The patch came out a shade darker than the belt.


I ran it through a slight bleach soak. After that, it was about as right as I could get it without messing it up. But before I installed the patches, I installed the washers with the Chicago screws. Then the patches were installed over all that hardware.



I also took the time to put some loop tape over the hardware on the back of the belt, as the screws and rivets scratched my armor during the last fitting.


I gave the clips on the thermal detonator a similar treatment.


One of the things pointed out during my fitting was my wandering right shoulder strap. Without the elastic loop to keep it in place, it wanders too far center (at least I'm hoping so; otherwise I'll have to remove and re-glue it). For those loops to work correctly, though, I'll need a wider cloth shoulder strap underneath it.

the Stunt CRL for Centurion specifies that the cloth part should be white, preferably elastic. This being the case, I decided to take the plunge, deconstruct the ANOVOS shoulder straps, and replace part of them with white elastic. First I took 2' wide elastic and cut two lengths equal to the length of the current ANOVOS straps. I sealed the ends with CA glue to prevent fraying.


Next I took apart the ANOVOS straps by cutting the threading with a hobby knife; then I used those pieces along with the white elastic to make the new shoulder straps. I hate sewing, though, and decide to use E6000 to glue everything together.




After letting them site for a day, they came out very good. I simply needed to use some extra glue and magnets to tap down some stray corners.


Besides that, I also:

*Added elastic cinches to my TK Boots to make getting them into the shin armor easier (loop tape on the heal helps with initial placement and tightening)


*Trimmed the hand guards down for better presentation (untrimmed one on left, trimmed one on right). Used a hollow sanding on the front and back to add some curvature for better fit.


* Cleaned up the eyes of my bucket with the Dremel sanding drum, a hobby knife, miniature files, sand paper, and raw nerves (messing up was not an option).

 

* Refitted the sniper knee for better fit (NEEDED MORE CLAMPS):


* Cleaned up the right shin from a mis-installed sniper knee (thanks Shingate!)


* Glued down the final edges of the flannel I installed on the bottom of the shins to prevent damage to Te TK Boots


* Painted the rivets and gluing down the ammo pack on the right thigh


* Covered up the inside ends of the split rivets with low-temp hot glue to avoid catching on the undersuit (or my skin, for that matter)


* Cleaned up the ABS paste fill I did on the bottom of the left thigh to get rid of a huge armor gap


* Added some strap loops inside the chest piece for my Pyle Pro amp, using spare ABS from the kit


Finally, I also worked on the fan system for my helmet. I finally determined where the fans would be placed. I measured and marked the blank for fan placement. Using one of the fans and a Dremel burr, I marked where to drill the mounting holes, and then used a drill but to drill them out. I also used a Dremel cutting disk to mark a cut-out for the fan blades, but not how you might think. The disk only provided the stencil.


Using the drill and a drywall bit, I was able to remove the circular section; then I used the Dremel sanding drum to clean it out.


I then marked and cut a square hole for the switch in a similar manner, using a hobby knife for the 90 degree corners. The holes to either side of the square cut-out will be used to mount the switch to the blank.


Lastly, I clean the blank of burrs, sanded it, and commenced to coat it with PlastiDip spray.


That's it for tonight. And after tonight, the only thing I'll really want to do before sending approval pics is finish the fan system and get the Pyle Pro mounted in the chest piece. I eventually want to PlastiDip the inside of my bucket, but I plan on doing that after approval (if I mess up, it will delay me getting good approval pics).

Monday, February 8, 2016

Back to the Grind (and Score and Snap...)

My son is all right, with a cast and a temp pin in his arm for the next 4-6 weeks, but already getting back to what 4 year olds do, thank goodness. Needless to say that I was occupied basically the whole weekend taking care of him. I finally got a moment to myself tonight.

But while I was spending some time with my son while taking the afternoon off from work, I decided I would try the score & snap approach to trimming the armor, or at least breaking pieces from the molds. And having already seen Trooperbay and others do it on YouTube, I gave it a shot on my thigh pieces, Pieces 20 - 23. All in all, it worked, with very minor slippage of the knife and workable rough cuts.


I cut around the inside arcs of the armor pieces, scored those lines, added relief scores, and popped them out like Trooperbay's method and what I did with the Dremel for the arms. When the score didn't want to split, I just scored it more until it popped. Since the pieces still need to be measured, cut, and fitted before final assemble, any roughness on the cuts doesn't concern me.


After the kids went to bed, I was able to get back into my work space and continue work on my forearm pieces.

One thing I immediately decided to do, based upon the fit and a reference shot of some film-used armor from posted on whitearmor, was to remove the elbow-side edge returns for easier wear and movement. I did this by making some rough cuts with the Dremel cutting disc, popping out those parts, cleaning up with the sanding drum, and finishing with some hand sanding. At the same time, I rough trimmed the strips in order to prep them for after the pieces were assembled, and to make removing the edge returns easier. Results were great.

The key is to fit, adjust, and refit. Remember: tape is cheap; armor is not. If you're like me, you'll probably use a lot of tape fitting and refitting as you go along. That's fine. It's better to measure twice, three, six times, etc., than to accidentally take off too much and permanently screw up a piece, or try to shim it back to fit.

EDIT: also, read this post for clarification between "edge returns" and "inside edges." As the arms pieces include no actual "edge returns," read the above and remainder as referring to "inside edges".


On the left forearm, I removed these edges with the pieces taped together; on the right, I removed them with the pieces disassembled and then taped them together to ensure a final fit. Either method was fine, I discovered.

With the final edge returns removed and the fit finally good, it was time to start assembling the two halves for each arm. I started with the front edge of each piece (the side with the ridged edge). I applied the E6000 to the alread-attached strip, placed the other piece on the strip, checked for alignment, and clamped/ set magnets. Because the raised edges form a valley inside the armor, I was limited with clamping as the larger clamps wouldn't fit into this valley on the left arm; the mold on the right arm was more forgiving and I was able to use two larger clamps on it.


Because I'm going to need to coerce the other edges together using larger clamps, and because I needed all my magnets for the front edges, I decided to only glue the front edges tonight. The back edges will get glued tomorrow once the front edges set, allowing the clamps to "muscle" the back edges together.


You can see the thermal detonator in that shot. Because I want to try to line up the strips on the biceps with the strips on the forearms as best I can, and I can't do that until the biceps are done gluing on both edges (and I REALLY didn't feel like starting to measure and fit the thighs yet), I decided to move away from the limbs for a moment and work on the detonator with was an easy build - and one I modified for extra use :)


I started by reading the instructions and the 501st ANH Hero specs, which go a long way towards telling you exactly how this piece should be assembled, even if you're not planning for 501st approval. After I understood the build, I put one of the caps on the end of the grey cylinder - this would be the left cap. I put the right cap on, dry a line to mark its edge, and carefully removed it. The caps have a super tight fit, but I want to be able to remove the right cap so I can use the cylinder as storage while trooping. After the cap was removed, I used the Dremel sanding drum on low to carefully sand down the right edge of the drum, hand sand with a small piece of sanding paper, and repeat, enough that I could remove the right cap without the contact becoming too loose.


After sanding the edge down to an acceptable level, I put the right cap on and went to the nearest door jam to draw a straight pencil line onto the tube, to line up the metal clips (the door jam trick is something I learned when I built model rockets with my dad as a kid). With the caps and line in place, it was easy enough to place the clips on, mark the holes, drill pilot holes with the drill, and screw the clips on. Later I will probably replace the screws with short machine bolts, nuts, and locking washers, so I can store stuff int eh cylinder without poking it with the screw ends.


With the clips installed, I cleaned up the edges of the control piece and sanded its back. I then placed it onto the grey cylinder (Just resting on the edges of the clip, facing up when attached to the belt, with the round part towards the trooper's right side) and marked with pencil its resting location. I sanded down the area on the grey cylinder for better cement adhesion, applied E6000 to the back of the white piece, placed it on the grey piece, and taped it down with masking tape.


I'm a storage container now, too! :D

Finally, I also took out some of the return edges in the armpits of my bicep pieces for better fit, in a similar fashion as the forearm pieces.



That was it for the night. Tomorrow I'll finish gluing the forearms and perhaps cut out the shin pieces so I can begin working on the legs as I finish up the arms and biceps.