Featured Post

The TKTalkie v4 - Press 6 for the Imperial March

Upgrading - the Path from v3.15 to v4.0 (Note: I had started this draft last year but never finished it, due to personal issues and cuttin...

Showing posts with label kidney. Show all posts
Showing posts with label kidney. Show all posts

Friday, May 11, 2018

Sound and Fury(ious Repairs and Overhauls)


BACK FROM THE DEAD A****LES!!!

I'm just kidding, I love you guys! But seriously, I'm FINALLY UPDATING THE BLOG WITH NEW INFO.

Happy belated May the 4th!

It's been too long since my last blog post. But like many, I'm never done working on my armor, and never done fiddling around with things, especially with people enabling me.

Armor Repair

Anovos armor is dainty in that it is thin in many places and likes to crack. Higher CRL approval requires some edge returns on torso armor to give the appearance of thick armor; lamentably, this often leads to cracking, which is especially true with the thin Anovos pulls.

As I mentioned in a previous blog, I reinforced the kidney plate with epoxy and fiberglass mesh to keep it from cracking, but the return edges just want to crack anyhow, especially near the ridge portion that runs up the back. Because the previous work prohibited me from repairing it on the inside of the edge, I had to work on the outside instead.


Although not as desirable of a repair, after sanding and polishing it's not terribly noticeable, especially when assembled next to the back plate.

Also thin are the ammo belt pieces for the main belt and thigh ammo pack.I reinforced these with thin, long scraps of ABS, CA glue, and much clamping. For the main ammo belt, I'll need to go back later and fill in some small cracks before they grow larger.


For the thing ammo pack, it had been cracked near the rivet hole during a photo shoot.I had to grind out the rack, fill with ABS paste, sand and polish; I also reinforced from behind with ABS strips and CA glue.


During the course of may troops the right cheek of my bucket developed a bend line. So I sanded it lightly, added some ABS paste, shaped, smoothed and polished. The ABS paste left some very tiny bubbles that I may fill later.


I had some tabs on the edge return of the butt plate that kept the armor from popping out too much compared to the kidney plate. Lamentably, this only caused the edge return to crack a lot, even with reinforcement. Thankfully, there was still plenty of inside edge return to apply a copious amount of Scrap ABS and ABS paste. I had to thoroughly paste the top as well due the edge return becoming uneven after cracking and repairs, to smooth the surface back out.


And... I got another crack in my chest plate, just past where I did all the reinforcement, of course. If what I did for the kidney plate pans out, I might due that to the chest plate as well, especially with a sanding block to help smooth and mold. Some edges of the chest plate have become uneven during past repairs, so I might just kill two birds with one stone, and thicken up that edge return for the entire edge.

But that's a topic for another blog post.

Fans/ Bucket

My bucket was a mess. I overbuilt it and it was hard to don and take off because the opening was narrower due to the oversized bracket. For reference:


I decided to move away from a bracketed design and instead use tape and hook & loop straps to secure fans and wiring directly to the inside of the bucket. Some of this had already been added, so there was plenty of fuzzy loop tape at strategic spots in the bucket. Hearing assist leads to the mics are held in place with copper tape, although it's admittedly not as resilient against EM noise from the wireless mic - but more on that in a moment.

I also (finally) replaced the wonky Anovos helmet harness and went with pads. Because my head is long, the top of my head needs to rest directly against the top of my bucket for me to see correctly through the eyes. however, placing pads front, back, and to the sides offers a lot of stability without compromising stability.


(Later I removed the forehead pad since it was causing my forehead some pain during my second May 4th troop. I'll need to troop without it, but so far the bucket still seems pretty stable and more comfortable without it.)

I'm also messing around with alternative fan methods. like using micro-fans instead of big blowers. Two micro-fans don't move as much air as a big blower, but they kept my bucket cool enough in the warm WonderCon main hall and made so little noise that I didn't need to use my hearing assist at all.


Even during 89 degree heat that I was in on May 4th, the mini fans did pretty well, but the analog speed controller I'm trying out is somewhat wasted upon them since they don't blow much air except at max speed. I'll be adding modular disconnects between the fans and controller so I can swap with the big blower fans and experiment between speed, noise, and cooling. Without the bracket, I can swap fans whenever I like.

As for the aforementioned wireless mic, I actually don't use it too often. The main reason, as I discovered at Comic-Con last year, is because in large groups it's possible that one's mic will pair with another's receiver, or vice versa. Nothing irritates me more than another person's voice cracking wise form my chestplate. Running a corded mic into my chest plate is the only way to guaranty that the voice coming out of my amp is MY OWN. Plus I need to run the cable from the sound glove anyhow, so it's a necessary evil.

Speaking of which...

TK-Talkie Sound Glove+ Update

Back in December of last year I started playing with TK Talkie firmware v3.15, a beta firmware that supported... a sound glove. Of course, the case (which I received from TK-Talkie) wasn't designed to support a sound glove, so I improvised by adding an RJ45 female jack to the case as a dongle, after wiring all the necessary pins on the Teensy board.


The sound glove itself is just a series of buttons attached to the hand, underneath the normal glove, using elastic straps. For my glove, I used four microswitch buttons and Cat5 cable, with each pair soldered to a button. Of course it connects to the TK-Talkie with an RJ45 male end.


I might change this design later to go with the TK-Talkie fashion of connecting sound gloves, which is 4-conductor 3.5mm jacks. v4 supports up to 6 buttons total, so typically 3 per glove (3 + ground = 4 conductors).

Initially, I had some issues with the buttons breaking off the wires, so I CA glued them onto scrap ABS backings, which I then sewed onto my elastic finger loops, for extra reinforcement.


My setup is slightly different, but here's Mr. TK-Talkie with his own sound glove for reference. I keep my buttons on my first knuckle on my left hand, whereas he puts them right on the fingertips of his right hand. It's just a matter of personal preference.

 

v3.15 was a beta version and worked well enough for the Hollywood Christmas Parade and our troop for an Anaheim Ducks game, but couldn't be configured with the app being a beta implementation (more of a proof-of-concept). Sound files had to be specifically named in a specific folder to work, so it was possible to change sounds, but couldn't be controlled per profile.

v4.00 on the other hand, paired with the v2 assistant app, adds those features and more. Sounds can be swapped on the fly. A button can be set to use the PTT/ Voice Activation/ Sleep function, used for two sounds, or used to adjust levels for various sounds on the box, like effects, voice, loops, etc. You can read more on TK-Talkie v4 here.

I was able to play with the v4 firmware and v2 app on May 4th, during troops at a children's play center and a wedding. It was endlessly fun to play the Imperial March on a whim, to tell people to "Move along, move along," or to inspect a wedding gift and verify that "These aren't the droids we're looking for."

There are endless possibilities, especially when one considers multiple profiles you can create on the TK-Talkie and then swap on a whim with the app. Look out San Diego Comic-Con! So even a basic TK can have some fun with the sound glove, on top of the other functions that the TK-Talkie supports and adds with v4 firmware - which I'll probably discuss at length in the next blog post.

Until next time, carry on troopers!

Wednesday, November 8, 2017

NOW SELLING - TKSnake's 5V Systems

It's been awhile since my last update.

The armor is still holding up, although I had to reinforce the butt plate and kidney plate with epoxy and fiberglass mesh, much like I did with the chest plate. I like to keep a bigger return edge on these pieces to make the armor look thicker, but the price for that is a higher chance of cracking. So the reinforcement was necessary to ensure that the armor would last for many years.

A while back I discovered how to lessen or eliminate EM noise in my USB-power Hearing Assist by using a DSL filter, which I published in a blog. Now, I don't mind sharing my info, but a later discovered that it was being used in a commercial venture, without even any acknowledgement.

Edit: For information about my offerings, please visit my Sales page!
(https://obsidiustk.blogspot.com/p/tksnakes-5v-systems.html)

Ordering

If you like what you see here, send an email to TK76235 (at) gmail (dot) com (I've broken the email address here to prevent spam bots from reading it). From there we can correspond and I can send you PayPal instructions to start your order.

My pal Brent at TK Talkie is also offering his system for sale if you aren't technically inclined to build your own. If you're interested in purchasing, tell him I sent you :)

So that's what I've been up to lately. I've already started building these for people in the Southern California Garrison, so now I'm offering my services to my first brotherhood, my fellow Anovos armor builders. If things go well I might start competing directly on whitearmor.net.

As an aside, TK Boots is sadly going out of business, so what they have in stock is up for grabs. If you like their boots, hit them up while you can.



Until next time...

Monday, November 14, 2016

EIB & Centurion: Left Side Split Rivets and Strapping

As I get closer to my goals of trying to get EIB and Centurion certification, I'm starting to go through the parts of the armor that need improving towards that goal, and also for a better fit.

One of those areas was the left side closure.

  • Using the original ANOVOS system, one rivets three H&L straps to one side of the closure and uses H&L tape on the other side to secure it, giving a wearable, removable closure.
  • When I did my closure, I modified the straps by cutting off the H&L pads on the straps, and then riveted them on both sides of the armor, making them non-removable but truer to the armor used on screen.
However, even during construction things were not up to snuff. As was pointed out to me back then, my rivet placement wasn't exactly correct. The problem originated from starting with the kidney plate, where I even spaced the rivets along the kidney plate. This causes a problem with the ab plate, which has a ridge that separates the cod piece from the ab plate proper. My placement resulted in the lower of the ab plate rivets being on this seam. For accuracy, this rivet should be above the seam, with the center rivet spaced evenly between the upper and lower rivet.

A picture from the original post that illustrates the issue.

In addition, after more than a few troops, it occurred to me that the canvas used with the ANOVOS kit has no give or stretch, meaning that if there's a bigger gap between the two plates, it's not going to be as easy to compensate for than with elastic. Further, the straps were held in place with the split rivets. If I had to replace them again in the future due to wear and tear, I'd have to redo all the split rivets again as well.

Resolved to correct the rivet placement and redo teh straps with less gap, the first step was to order some new split rivets, which I did through a member on whitearmor. Once those arrived, it was just a matter of removing the old split rivets and the attached strapping.



 I used a set of needle-nose pliers to un-set the rivets and pull them out without damaging the armor. Once that was done, I had three clean holes on either plate that I needed to seal up with ABS paste. I did this by taping up the front of the plate and filling in from the back.



I wish this would have worked better, but I ended up having to do some front fill as well, and then the typical sanding with 150 - 350 - 600 wet - 1500 wet until the fills were smooth as the surrounding plastic.

I could probably do this in my sleep now,
I've done it so many times...

Finish with Novus 3, 2, and 1 to make everything shiny again. No I have a pristine surface to make new-accurate holes for my rivets.


 I used the following measurements which I followed from USKWrath's post on the matter:

Ab plate:

  • Top rivet: 20mm from top, 10mm from plate edge
  • Bottom rivet, 10mm from cod plate edge, 10mm from plate edge
  • Center rivet: halfway between top and bottom rivets (~63mm either way), 10mm from plate edge
I then put corresponding markings in the kidney plate for the spacing, 10mm from the plate edge. The markings are shown here:



Measure twice, cut once, they say. After satisfied with the measurements, it was time to cut drill the new holes and fasten the rivets. After scuffing the heads with some 150 grit sandpaper to prepare them for future painting, I put them in place using a snap head set, mallet, small chisel, and flat punch tool. For those who aren't familiar, there are six rivets total - three in the ab plate and three in the kidney plate.



You'll note that the rivets were fastened without the strapping in place. This was done on purpose. Taking a page to the common way people fasten garter loops to the inside of thigh assemblies, I decided to fasten the new strapping directly to the inside of the ab and kidney plates using nothing but E6000. This way, the straps would be easy to replace in the future. I used some spare 2" black elastic strapping left over from when I redid my thigh garters. I started by gluing them to the kidney plate, waiting a day, and then gluing them to the ab plate.



As you can see, the results are pretty tight. the bond is strong, and the straps are tight yet stretchy, allowing for a better fit and some give if I end up bending in an unusual manner.

I would have actually placed the bottom strap lower, but I have to leave room for the strapping that secures the kidney plate to the butt plate, as that uses a H&L tape system. Plus, the belt helps keep the pieces together around this area.

After all was said and done, I carefully painted the new rivet heads with Testor white enamel paint.

I also had an issue with the cod strap coming off its split rivet, so I redid this rivet as well, using some scrap ABS to make a large washer so that the hole in the elastic strap wouldn't slip off the small washer included with the rivet set.

And then I had to re-redo it since I reinstalled the strap upside-down.
But you get the picture.

Another recent mod I did was thigh fit. Remember how I lost a bit of weight to fit into my armor better? Most of that weight came off of my stomach, but some also came off my thighs. The problem was that, with the thighs already shimmed, the pieces are actually a little bigger than my thighs now <facepalm>. So what I did was add some foam padding to the inside rear of my thighs to keep the fronts f my thighs against the front of my legs. This resolved an issue wherein the drop-down boxes on my belt kept getting caught on the upper front edges of my thigh pieces, leading to issues walking (thankfully the drop-downs and thighs didn't suffer damage). I haven't decided it it's worth the risk of removing the thigh shims to make the thighs better, but so far I'm leaning to leaving them in, so long as they don't affect the armor's overall look too badly.

Next up on the list is adding a hearing assist system to the bucket to help with, well, hearing, but especially when I run the new blower fans. I plan to run both fans and hearing assist from a new USB battery bank instead of having to worry about AA batteries. Stay tuned...

Saturday, April 9, 2016

Final Touches Pt 1 - Let's Touch ALL THE PIECES

As I get into the final stretch of this build before submitting for the 501st as IEB (Tier 2), I need to correct the issues I found during my last fitting.


First, I started with the rivets on the left side of the armor. I scuffed up the heads with 350 grit sandpaper, being careful not to scuff the armor, and then painted them gloss white per the CRL.

Next I wanted to tackle the extra Chicago screws in the belt that are not in the Stunt CRL but have been installed by ANOVOS. Instead of removing them and covering up the holes, I doubled down and not only kept them, but added washers to the upper two. The reason behind this was that I've already seen the two remaining screws tear through a few ANOVOS belts, so I wanted to keep all the screws to give the belt extra strength - not only that, but reinforce the upper two screws, as I was going to cover them up with iron-on patchwork.

My main issue is that the patch I had was too white. So to rectify this, I made a tea bath to stain the patch off white; then, I soaked the patch in the tea bath for less than a minute.


The patch came out a shade darker than the belt.


I ran it through a slight bleach soak. After that, it was about as right as I could get it without messing it up. But before I installed the patches, I installed the washers with the Chicago screws. Then the patches were installed over all that hardware.



I also took the time to put some loop tape over the hardware on the back of the belt, as the screws and rivets scratched my armor during the last fitting.


I gave the clips on the thermal detonator a similar treatment.


One of the things pointed out during my fitting was my wandering right shoulder strap. Without the elastic loop to keep it in place, it wanders too far center (at least I'm hoping so; otherwise I'll have to remove and re-glue it). For those loops to work correctly, though, I'll need a wider cloth shoulder strap underneath it.

the Stunt CRL for Centurion specifies that the cloth part should be white, preferably elastic. This being the case, I decided to take the plunge, deconstruct the ANOVOS shoulder straps, and replace part of them with white elastic. First I took 2' wide elastic and cut two lengths equal to the length of the current ANOVOS straps. I sealed the ends with CA glue to prevent fraying.


Next I took apart the ANOVOS straps by cutting the threading with a hobby knife; then I used those pieces along with the white elastic to make the new shoulder straps. I hate sewing, though, and decide to use E6000 to glue everything together.




After letting them site for a day, they came out very good. I simply needed to use some extra glue and magnets to tap down some stray corners.


Besides that, I also:

*Added elastic cinches to my TK Boots to make getting them into the shin armor easier (loop tape on the heal helps with initial placement and tightening)


*Trimmed the hand guards down for better presentation (untrimmed one on left, trimmed one on right). Used a hollow sanding on the front and back to add some curvature for better fit.


* Cleaned up the eyes of my bucket with the Dremel sanding drum, a hobby knife, miniature files, sand paper, and raw nerves (messing up was not an option).

 

* Refitted the sniper knee for better fit (NEEDED MORE CLAMPS):


* Cleaned up the right shin from a mis-installed sniper knee (thanks Shingate!)


* Glued down the final edges of the flannel I installed on the bottom of the shins to prevent damage to Te TK Boots


* Painted the rivets and gluing down the ammo pack on the right thigh


* Covered up the inside ends of the split rivets with low-temp hot glue to avoid catching on the undersuit (or my skin, for that matter)


* Cleaned up the ABS paste fill I did on the bottom of the left thigh to get rid of a huge armor gap


* Added some strap loops inside the chest piece for my Pyle Pro amp, using spare ABS from the kit


Finally, I also worked on the fan system for my helmet. I finally determined where the fans would be placed. I measured and marked the blank for fan placement. Using one of the fans and a Dremel burr, I marked where to drill the mounting holes, and then used a drill but to drill them out. I also used a Dremel cutting disk to mark a cut-out for the fan blades, but not how you might think. The disk only provided the stencil.


Using the drill and a drywall bit, I was able to remove the circular section; then I used the Dremel sanding drum to clean it out.


I then marked and cut a square hole for the switch in a similar manner, using a hobby knife for the 90 degree corners. The holes to either side of the square cut-out will be used to mount the switch to the blank.


Lastly, I clean the blank of burrs, sanded it, and commenced to coat it with PlastiDip spray.


That's it for tonight. And after tonight, the only thing I'll really want to do before sending approval pics is finish the fan system and get the Pyle Pro mounted in the chest piece. I eventually want to PlastiDip the inside of my bucket, but I plan on doing that after approval (if I mess up, it will delay me getting good approval pics).