Featured Post

The TKTalkie v4 - Press 6 for the Imperial March

Upgrading - the Path from v3.15 to v4.0 (Note: I had started this draft last year but never finished it, due to personal issues and cuttin...

Showing posts with label abdomen. Show all posts
Showing posts with label abdomen. Show all posts

Monday, November 14, 2016

EIB & Centurion: Left Side Split Rivets and Strapping

As I get closer to my goals of trying to get EIB and Centurion certification, I'm starting to go through the parts of the armor that need improving towards that goal, and also for a better fit.

One of those areas was the left side closure.

  • Using the original ANOVOS system, one rivets three H&L straps to one side of the closure and uses H&L tape on the other side to secure it, giving a wearable, removable closure.
  • When I did my closure, I modified the straps by cutting off the H&L pads on the straps, and then riveted them on both sides of the armor, making them non-removable but truer to the armor used on screen.
However, even during construction things were not up to snuff. As was pointed out to me back then, my rivet placement wasn't exactly correct. The problem originated from starting with the kidney plate, where I even spaced the rivets along the kidney plate. This causes a problem with the ab plate, which has a ridge that separates the cod piece from the ab plate proper. My placement resulted in the lower of the ab plate rivets being on this seam. For accuracy, this rivet should be above the seam, with the center rivet spaced evenly between the upper and lower rivet.

A picture from the original post that illustrates the issue.

In addition, after more than a few troops, it occurred to me that the canvas used with the ANOVOS kit has no give or stretch, meaning that if there's a bigger gap between the two plates, it's not going to be as easy to compensate for than with elastic. Further, the straps were held in place with the split rivets. If I had to replace them again in the future due to wear and tear, I'd have to redo all the split rivets again as well.

Resolved to correct the rivet placement and redo teh straps with less gap, the first step was to order some new split rivets, which I did through a member on whitearmor. Once those arrived, it was just a matter of removing the old split rivets and the attached strapping.



 I used a set of needle-nose pliers to un-set the rivets and pull them out without damaging the armor. Once that was done, I had three clean holes on either plate that I needed to seal up with ABS paste. I did this by taping up the front of the plate and filling in from the back.



I wish this would have worked better, but I ended up having to do some front fill as well, and then the typical sanding with 150 - 350 - 600 wet - 1500 wet until the fills were smooth as the surrounding plastic.

I could probably do this in my sleep now,
I've done it so many times...

Finish with Novus 3, 2, and 1 to make everything shiny again. No I have a pristine surface to make new-accurate holes for my rivets.


 I used the following measurements which I followed from USKWrath's post on the matter:

Ab plate:

  • Top rivet: 20mm from top, 10mm from plate edge
  • Bottom rivet, 10mm from cod plate edge, 10mm from plate edge
  • Center rivet: halfway between top and bottom rivets (~63mm either way), 10mm from plate edge
I then put corresponding markings in the kidney plate for the spacing, 10mm from the plate edge. The markings are shown here:



Measure twice, cut once, they say. After satisfied with the measurements, it was time to cut drill the new holes and fasten the rivets. After scuffing the heads with some 150 grit sandpaper to prepare them for future painting, I put them in place using a snap head set, mallet, small chisel, and flat punch tool. For those who aren't familiar, there are six rivets total - three in the ab plate and three in the kidney plate.



You'll note that the rivets were fastened without the strapping in place. This was done on purpose. Taking a page to the common way people fasten garter loops to the inside of thigh assemblies, I decided to fasten the new strapping directly to the inside of the ab and kidney plates using nothing but E6000. This way, the straps would be easy to replace in the future. I used some spare 2" black elastic strapping left over from when I redid my thigh garters. I started by gluing them to the kidney plate, waiting a day, and then gluing them to the ab plate.



As you can see, the results are pretty tight. the bond is strong, and the straps are tight yet stretchy, allowing for a better fit and some give if I end up bending in an unusual manner.

I would have actually placed the bottom strap lower, but I have to leave room for the strapping that secures the kidney plate to the butt plate, as that uses a H&L tape system. Plus, the belt helps keep the pieces together around this area.

After all was said and done, I carefully painted the new rivet heads with Testor white enamel paint.

I also had an issue with the cod strap coming off its split rivet, so I redid this rivet as well, using some scrap ABS to make a large washer so that the hole in the elastic strap wouldn't slip off the small washer included with the rivet set.

And then I had to re-redo it since I reinstalled the strap upside-down.
But you get the picture.

Another recent mod I did was thigh fit. Remember how I lost a bit of weight to fit into my armor better? Most of that weight came off of my stomach, but some also came off my thighs. The problem was that, with the thighs already shimmed, the pieces are actually a little bigger than my thighs now <facepalm>. So what I did was add some foam padding to the inside rear of my thighs to keep the fronts f my thighs against the front of my legs. This resolved an issue wherein the drop-down boxes on my belt kept getting caught on the upper front edges of my thigh pieces, leading to issues walking (thankfully the drop-downs and thighs didn't suffer damage). I haven't decided it it's worth the risk of removing the thigh shims to make the thighs better, but so far I'm leaning to leaving them in, so long as they don't affect the armor's overall look too badly.

Next up on the list is adding a hearing assist system to the bucket to help with, well, hearing, but especially when I run the new blower fans. I plan to run both fans and hearing assist from a new USB battery bank instead of having to worry about AA batteries. Stay tuned...

Saturday, April 9, 2016

Final Touches Pt 1 - Let's Touch ALL THE PIECES

As I get into the final stretch of this build before submitting for the 501st as IEB (Tier 2), I need to correct the issues I found during my last fitting.


First, I started with the rivets on the left side of the armor. I scuffed up the heads with 350 grit sandpaper, being careful not to scuff the armor, and then painted them gloss white per the CRL.

Next I wanted to tackle the extra Chicago screws in the belt that are not in the Stunt CRL but have been installed by ANOVOS. Instead of removing them and covering up the holes, I doubled down and not only kept them, but added washers to the upper two. The reason behind this was that I've already seen the two remaining screws tear through a few ANOVOS belts, so I wanted to keep all the screws to give the belt extra strength - not only that, but reinforce the upper two screws, as I was going to cover them up with iron-on patchwork.

My main issue is that the patch I had was too white. So to rectify this, I made a tea bath to stain the patch off white; then, I soaked the patch in the tea bath for less than a minute.


The patch came out a shade darker than the belt.


I ran it through a slight bleach soak. After that, it was about as right as I could get it without messing it up. But before I installed the patches, I installed the washers with the Chicago screws. Then the patches were installed over all that hardware.



I also took the time to put some loop tape over the hardware on the back of the belt, as the screws and rivets scratched my armor during the last fitting.


I gave the clips on the thermal detonator a similar treatment.


One of the things pointed out during my fitting was my wandering right shoulder strap. Without the elastic loop to keep it in place, it wanders too far center (at least I'm hoping so; otherwise I'll have to remove and re-glue it). For those loops to work correctly, though, I'll need a wider cloth shoulder strap underneath it.

the Stunt CRL for Centurion specifies that the cloth part should be white, preferably elastic. This being the case, I decided to take the plunge, deconstruct the ANOVOS shoulder straps, and replace part of them with white elastic. First I took 2' wide elastic and cut two lengths equal to the length of the current ANOVOS straps. I sealed the ends with CA glue to prevent fraying.


Next I took apart the ANOVOS straps by cutting the threading with a hobby knife; then I used those pieces along with the white elastic to make the new shoulder straps. I hate sewing, though, and decide to use E6000 to glue everything together.




After letting them site for a day, they came out very good. I simply needed to use some extra glue and magnets to tap down some stray corners.


Besides that, I also:

*Added elastic cinches to my TK Boots to make getting them into the shin armor easier (loop tape on the heal helps with initial placement and tightening)


*Trimmed the hand guards down for better presentation (untrimmed one on left, trimmed one on right). Used a hollow sanding on the front and back to add some curvature for better fit.


* Cleaned up the eyes of my bucket with the Dremel sanding drum, a hobby knife, miniature files, sand paper, and raw nerves (messing up was not an option).

 

* Refitted the sniper knee for better fit (NEEDED MORE CLAMPS):


* Cleaned up the right shin from a mis-installed sniper knee (thanks Shingate!)


* Glued down the final edges of the flannel I installed on the bottom of the shins to prevent damage to Te TK Boots


* Painted the rivets and gluing down the ammo pack on the right thigh


* Covered up the inside ends of the split rivets with low-temp hot glue to avoid catching on the undersuit (or my skin, for that matter)


* Cleaned up the ABS paste fill I did on the bottom of the left thigh to get rid of a huge armor gap


* Added some strap loops inside the chest piece for my Pyle Pro amp, using spare ABS from the kit


Finally, I also worked on the fan system for my helmet. I finally determined where the fans would be placed. I measured and marked the blank for fan placement. Using one of the fans and a Dremel burr, I marked where to drill the mounting holes, and then used a drill but to drill them out. I also used a Dremel cutting disk to mark a cut-out for the fan blades, but not how you might think. The disk only provided the stencil.


Using the drill and a drywall bit, I was able to remove the circular section; then I used the Dremel sanding drum to clean it out.


I then marked and cut a square hole for the switch in a similar manner, using a hobby knife for the 90 degree corners. The holes to either side of the square cut-out will be used to mount the switch to the blank.


Lastly, I clean the blank of burrs, sanded it, and commenced to coat it with PlastiDip spray.


That's it for tonight. And after tonight, the only thing I'll really want to do before sending approval pics is finish the fan system and get the Pyle Pro mounted in the chest piece. I eventually want to PlastiDip the inside of my bucket, but I plan on doing that after approval (if I mess up, it will delay me getting good approval pics).

Monday, March 28, 2016

Testing the Torso and Truncating my Trunk

I finished strapping up the torso by adding the chest and back plates. I don't have any pictures of the straps, but it's basically straight out of the ANOVOS instructions for these sections - four of the longer H&L straps, two per piece, to connect the chest to the ab plate and the back to the kidney plate. Then, connected at the top with the T-shaped shoulder straps. The final look, once donned, is impressive :)


One thing I noticed is that the ab and kidney plate likes to separate near the bottom, due to the slight gut I have. I guess I'll need to work out and wear a girdle in the mean time. It's the only place on my body that's overly fatty.


Additionally, the modified ANOVOS belt seems to be working well enough. The only thing left to do with it is to remove or cover up the upper two Chicago screws to qualify for Stunt Basic or EIB certification for the 501st. I plan to do this with small circular pieces of iron-on canvas patch, after I try adding some washers to the screws to reduce the chances of the holster tearing through the belt.

After the fitting, I finished trimming and gluing the painted ab buttons in place.


There were some places on the armor that had obvious rub, like the back plate into my shoulders and the posterior plate into my inner legs. So I sanded these down with the Dremel sanding drum to eliminate and taper inner edges.



I also noticed, as I did on my friend's armor during the armor party, that the posterior plate likes to stick out. To combat this, I added to two tabs on the inside of the piece, on the edge returns, so that the plate would hook behind the kidney plate when strapped into place.


I'd honestly be about done at this point, but after fitting the thighs some more, it occurred to me that, although I have the thighs properly trimmed for length, I don't have them trimmed for shape. However, more importantly, they don't come up as far as I need them to (when I'm standing). They're too tight, especially near the top where almost no material was trimmed (save the front edge returns). Therefore, I'll have to accept the fact that I need to shim them. I've already started this process, but will make another blog post dedicated entirely to the process. Until then...