Featured Post

The TKTalkie v4 - Press 6 for the Imperial March

Upgrading - the Path from v3.15 to v4.0 (Note: I had started this draft last year but never finished it, due to personal issues and cuttin...

Saturday, April 9, 2016

Final Touches Pt 1 - Let's Touch ALL THE PIECES

As I get into the final stretch of this build before submitting for the 501st as IEB (Tier 2), I need to correct the issues I found during my last fitting.


First, I started with the rivets on the left side of the armor. I scuffed up the heads with 350 grit sandpaper, being careful not to scuff the armor, and then painted them gloss white per the CRL.

Next I wanted to tackle the extra Chicago screws in the belt that are not in the Stunt CRL but have been installed by ANOVOS. Instead of removing them and covering up the holes, I doubled down and not only kept them, but added washers to the upper two. The reason behind this was that I've already seen the two remaining screws tear through a few ANOVOS belts, so I wanted to keep all the screws to give the belt extra strength - not only that, but reinforce the upper two screws, as I was going to cover them up with iron-on patchwork.

My main issue is that the patch I had was too white. So to rectify this, I made a tea bath to stain the patch off white; then, I soaked the patch in the tea bath for less than a minute.


The patch came out a shade darker than the belt.


I ran it through a slight bleach soak. After that, it was about as right as I could get it without messing it up. But before I installed the patches, I installed the washers with the Chicago screws. Then the patches were installed over all that hardware.



I also took the time to put some loop tape over the hardware on the back of the belt, as the screws and rivets scratched my armor during the last fitting.


I gave the clips on the thermal detonator a similar treatment.


One of the things pointed out during my fitting was my wandering right shoulder strap. Without the elastic loop to keep it in place, it wanders too far center (at least I'm hoping so; otherwise I'll have to remove and re-glue it). For those loops to work correctly, though, I'll need a wider cloth shoulder strap underneath it.

the Stunt CRL for Centurion specifies that the cloth part should be white, preferably elastic. This being the case, I decided to take the plunge, deconstruct the ANOVOS shoulder straps, and replace part of them with white elastic. First I took 2' wide elastic and cut two lengths equal to the length of the current ANOVOS straps. I sealed the ends with CA glue to prevent fraying.


Next I took apart the ANOVOS straps by cutting the threading with a hobby knife; then I used those pieces along with the white elastic to make the new shoulder straps. I hate sewing, though, and decide to use E6000 to glue everything together.




After letting them site for a day, they came out very good. I simply needed to use some extra glue and magnets to tap down some stray corners.


Besides that, I also:

*Added elastic cinches to my TK Boots to make getting them into the shin armor easier (loop tape on the heal helps with initial placement and tightening)


*Trimmed the hand guards down for better presentation (untrimmed one on left, trimmed one on right). Used a hollow sanding on the front and back to add some curvature for better fit.


* Cleaned up the eyes of my bucket with the Dremel sanding drum, a hobby knife, miniature files, sand paper, and raw nerves (messing up was not an option).

 

* Refitted the sniper knee for better fit (NEEDED MORE CLAMPS):


* Cleaned up the right shin from a mis-installed sniper knee (thanks Shingate!)


* Glued down the final edges of the flannel I installed on the bottom of the shins to prevent damage to Te TK Boots


* Painted the rivets and gluing down the ammo pack on the right thigh


* Covered up the inside ends of the split rivets with low-temp hot glue to avoid catching on the undersuit (or my skin, for that matter)


* Cleaned up the ABS paste fill I did on the bottom of the left thigh to get rid of a huge armor gap


* Added some strap loops inside the chest piece for my Pyle Pro amp, using spare ABS from the kit


Finally, I also worked on the fan system for my helmet. I finally determined where the fans would be placed. I measured and marked the blank for fan placement. Using one of the fans and a Dremel burr, I marked where to drill the mounting holes, and then used a drill but to drill them out. I also used a Dremel cutting disk to mark a cut-out for the fan blades, but not how you might think. The disk only provided the stencil.


Using the drill and a drywall bit, I was able to remove the circular section; then I used the Dremel sanding drum to clean it out.


I then marked and cut a square hole for the switch in a similar manner, using a hobby knife for the 90 degree corners. The holes to either side of the square cut-out will be used to mount the switch to the blank.


Lastly, I clean the blank of burrs, sanded it, and commenced to coat it with PlastiDip spray.


That's it for tonight. And after tonight, the only thing I'll really want to do before sending approval pics is finish the fan system and get the Pyle Pro mounted in the chest piece. I eventually want to PlastiDip the inside of my bucket, but I plan on doing that after approval (if I mess up, it will delay me getting good approval pics).

Tuesday, April 5, 2016

Fit, for Imperial Consumption

I've been working on this armor on and off since 31 January. I figured it was about time to throw it all on and see how everything fits together.

With some help from my wife, getting our older child to bed and then helping me with the thermal detonator and the right shoulder bell, I was able to get everything on.

Assembly happened in the following order:
  • Socks and underwear
  • Compression pants
  • Neck seal
  • Compression shirt
  • Ab garter (for my gut, underneath shirt)
  • Thigh garter belt (over shirt)
  • Thigh armor
  • TK Boots
  • Shin armor
  • Ab armor/ posterior plate/ kidney plate/ belt/ back plate (hanging from kidney plate))
  • Chest plate (moving back plate into position)
  • Fastened belt
  • Arm armor (already connected to each other)
  • Fastened shoulder bells to straps (assist from wife)
  • Thermal detonator (assist from wife)
  • Gloves
  • Hand Guards
  • Helmet
Here's the initial look:



My initial findings:

  • I need some tape or low-temp hot glue over the split rivets, especially for the right knee. The rivet ends like to poke into my undersuit and skin (ouch).
  • I need some white H&L tape to help cinch the TK boots to my legs to help with fitting the shin armor 
  • My left kneecap was getting pinched between the thigh and front of the shin. I trimmed that part of the shin. I might also get some foam to put behind the front of the shins to add extra cushion.
  • The back of my left knee was getting pinched between the thigh and shin armors. My thigh pieces are sitting too low, but especially my left thigh. I adjusted the loop tape in both thighs to be optimal and as symmetrical as possible (so the thighs are at the same height).
  • The snap loops for the garter belt were twisting. I'll attempt to reinforce these with E6000 to help them keep their shape. I may also try using them inverted to help control torsion.
  • I need to finish mounting my helmet fans; that bucket's like a sauna.
  • Still need to paint some of those rivets white.
  • Tighten that garter belt to keep the right side from popping out near the bottom (and do some crunches :P ).

After passing it into the FB ANOVOS group, they offered the following additional comments:

  • Right shoulder strap seems off. If making the strap keepers doesn't adjust it properly, I may need to re-mount it. Bothersome, but doable.
  • I need to trim my hand guards and adjust for fit. Making a hollow sand (curving in towards the middle) is my first thought, but I'll also probably trim the total thickness. I honestly haven't trimmed this since cutting them out of the blanks.
  • The bucket seems a bit high. I did modify the fit for the stock ANOVOS helmet strap to sit farther back to accommodate my glasses inside the bucket. I'll have to ensure this ins't causing any issues, or else mount old glasses inside the bucket instead and re-mount the head strap.
My wife is impressed and posted a picture to FB. My stepmother asked, "Is it done done or does it still need final fitting and tweaking?" She owns a '68 Mustang (not the sport version, mind you) that's been restored a few times (the salt they use on Midwestern winter roads doesn't help classic cars), so I replied, "It's like your Mustang; it's never really done :-P But it's pretty close to being ready for trooping ;-)"

That being said, it seems that I only have some minor fixes to make before being ready for my approval photos, which I plan to do at my squad's next armor party on 17 April at the latest. That should give me plenty of time to buff out the scratches on my right shin due to the colloquially-named "Shin-gate," as well as working on the minor issues above.

In addition, my squad had a bulk buy-in from HyperFirm. I would love to have the time and patience to tweak my Disney blaster into something more screen-accurate, but ultimately it wouldn't be fit for Centurion, which I'd like to eventually get once I piecemeal more items together (like a Kittle belt and latex hand guards). All in all, I'm getting an Elite E-11 for the piece of a standard E-11. And once again, my wife supported me, thanks to us having a little extra money.

More blog posts will come as I continue these minor tweaks and personal touches, until I'm 501st certified :) Until the next post...

The Thigh (Re)Master Pt 2 - Get In Shape, Thighs!

Edit: DO NOT trim thighs for length until the end of your build. Mistakes were made. Consider the following a cautionary tale.

With the thighs now properly shimmed, it was time to start fitting them to the garter belt and straps and, almost as important, reforming the shape I lost when I trimmed them down.

As one critic pointed out, after the armor party, my thighs weren't looking very much like TK thighs after I did some moderate trimming for length. I chopped off the peaks and ended up rounding them off.


Since then, I had planned to re-shape the thighs. However, initial fitting revealed shimming would be required so getting into the thighs wouldn't feel like squeezing my legs into funnels. That being done, I was now set to trim the upper outside edges into the proper TK shape.

Unfortunately, I was initially overzealous with the trimming and botched the shape on the right thigh. Sigh. That's what I get for trying to bang it out before bed. Well, at least I had a lot of experience with shimming. SO I added part of the cut section back on and shimmed it. Thankfully, it took a lot less time than shimming the back of the thighs.


While I was working on that, I trimmed the left thigh. For both pieces, I simply freehand drew the shape I wanted to cut, going down a total of 1.5" max from the top, cutting the shpe out with the Dremel cutting disk, and then hand sanding the new edge.


Using the new garter belt system, I placed the ANOVOS thigh straps onto the snap mounts and marked where the top of the thigh met the strap. I was then able to use this measure to help determine where to place the loop tape inside the thigh, although I did have to tweak it a few times afterwards. I used a longer length of loop tape to allow for minor adjustments.


And with that, I was at the end of the ANOVOS instruction guide. All pieces have been cut, fitted, assembled, and in some cases modified for better wear-ability. Now it was time to throw everything on and see how it fits together. That will be in the next blog entry.

Monday, April 4, 2016

Strapping Extremities

In addition to the thigh pieces, I also worked on strapping for my arm pieces, and a garter system for the thighs.

First, I'll mention that I did finally receive my soft parts from ANOVOS on Good Friday. But since my office was closed, I didn't actually get them until the following Monday. The ANOVOS undersuit is actually more loose than the stuff I purchased on Amazon, but still fits well. The rubber gloves are what I'll be using to certify for EIB for the 501st.

Now let's talk about the arms. I basically did the arms up per the ANOVOS instructions. I used some longer pieces of H&L tape inside the shoulder bells to help with adjusting placement for the bicep pieces.


After fitting, I decided there was too much inside edge in the shoulder bells for comfort; after all, these were some of the first pieces I trimmed and haven't been retouched until now. I removed a bit of it not only helped with the margin between the bells and the biceps, but also improved flexibility of the bell pieces to give them more give.


As for the thigh pieces, in preparation for finishing this project, I decided that, like many out there, I didn't want to attach the thighs to the inside of the ab plate as per ANOVOS instructions. Instead, I decided to create a garter belt system like many troopers use, but incorporate the parts from ANOVOS to make the build easier, and more adjustable thanks to the H&L tape.

I rummaged around and found an old untrimmed (full length) web belt that was a "field find" from my paintballing days. The first thing I did was unravel it and apply a fresh coat of dye (I used some leather dye I already owned). I did end up taking off the buckle and belt tip for this project after the pictures were taken.



I let the dye dry overnight and then put the belt through a few wash cycles to knock out excess dye - no need getting that on the inside of my armor pieces. Once it was dry, I trimmed the belt for size, leaving me a sizable amount for the next part of the project.

Next, I made loops to fit over the belt that would hold the ANAOVOS snaps for the thigh straps. Because the snap plates were longer than the width of the belt, I didn't have to worry too much about making these too small to fit over the belt. I took two 6" strips of web belt scrap, folded them in half, and then used a leather punch and small leather rivets (again, stuff I already had) to create the loops. I used CA glue on the edges of the webbing to keep them from fraying (I did the same with the actual belt as well).


The snap plates themselves were wider than the webbing; therefore, I removed 5mm from each edge of the plates to fit them to the web loops, using the old score & snap method.


Finally, I attached the plates to the side of the loop that would face INSIDE towards my body, using E6000 cement and excessive clamping. The reason is because the straps were designed to fasten to the ab plate, and the snaps open opposite to the hook tape that fastens to the loop tape to be attached to the inside of the thighs.


Once I'm done reshaping the thigh pieces, I'll be testing this system out to ensure it will stand up to good trooping. Until then...

The Thigh (Re)Master Pt 1 - Shimmy Shimmy Shake

As I mentioned in my last post, after fitting the thighs some more, it occurred to me that, although I have the thighs properly trimmed for length, I don't have them trimmed for shape. However, more importantly, they don't come up as far as I need them to (when I'm standing). They're too tight, especially near the top where almost no material was trimmed (save the front edge returns). Therefore, I'll have to accept the fact that I need to shim them.

To begin, I found scrap ABS strips of the appropriate length and width (> 1"). However, to get more width, I decided to use a hot water bath to flatten them out. I did this using a pot of boiling water and two cutting boards to act as presses. The pieces ended coming out a little curved, which is fine since the back of my thighs (where the pieces will be going) are also curved; the pieces are also flexible, so getting them in place should be a big deal.


I also made some ABS hooks for my bicep pieces (should I need them) while I was at it, to add to the biceps to hook the shoulder bell straps as many troopers do. It was simple enough to add the hooks using a hot water bath, small tongs, and my Gorilla Grip gloves.


I separated the thighs in the back, with the center strip attached to the outside piece; teh shims will be added to the inner thigh piece. After creating the shims, I cut them to a rough length and taped them in. I found that, with the shims at full width, they made the pieces too big, which is a good thing - it's easy to trim down the shims, but harder to find bigger pieces to use as shims if they're too small. I performed additional measuring and fitting without the shims to determine the best width. I trimmed them to 1" width top and bottom, making sure both edges were straight. I may trim more near the bottom after I get the shims permanently attached, when it will be easier to do more test fitting.


With the shims ready, I created six splints, three for each thigh for top, bottom, and center. The splits would hold the shim in place while I used ABS paste to cement them to the inner thigh pieces. Because this will be a permanent fixture, I used CA glue to cement the splints to the inner thigh pieces, and then the shims.


I then used ABS paste to attach the shims to the armor. In retrospect, I wish I had used some CA gel first, and then ABS paste - you'll see why in a moment. Also, when applying ABS paste to shims, I recommend applying it with your fingers using a latex glove, to reduce the lumpiness of the paste. I did NOT do this on my first application, and the outcome was a bit gloppy, requiring a lot of sanding to be flush.

Speaking of sanding, after the paste was dry, I hit large lumps with the Dremel sanding drum, then used a sanding block with 150 grit. I wish I had some lower grit paper, because this step took longer at 150 grit. However, once everything was flat, I followed up with 350 grit, 600 grit, and then 600 grit wet sanding to make everything as smooth as possible before polishing.


For polishing, I used Novos 3, then NBovos 2, to work out the deeper scratches and then polish up. I found that, for scratches that wouldn't come out with Novos 3, additional wet sanding with the 600 grit paper was necessary. The shims came out alright after this was all said and done.



Once finished, and after taping up again to confirm fit one last time, I cemented the back of the thighs back together with E6000.

But as is the case with many of my projects, this part did not go off without a hitch. lamentably, when I was getting the pieces back together, the shims cracked near the knees. This is why I wish I'd used CA gel to fasten them to the parent piece before applying ABS paste.


I let the E6000 cure first. Then, I fixed the cracks by first applying CA liquid (to get into the crack) and holding the pieces in place until the glue set. Then, I covered the crack with an amount of ABS paste applied by finger for minimal coating. Once it dried, I was forced to apply the entire sanding and polishing process all over again.


After this, the shims were done for the most part; however, there are some visible lines on the shims that I may need to address before approval. However, I still need to apply the strapping system to the thighs, as well as fix the shape on the top. I'll be covering this in a future post. 

Monday, March 28, 2016

Testing the Torso and Truncating my Trunk

I finished strapping up the torso by adding the chest and back plates. I don't have any pictures of the straps, but it's basically straight out of the ANOVOS instructions for these sections - four of the longer H&L straps, two per piece, to connect the chest to the ab plate and the back to the kidney plate. Then, connected at the top with the T-shaped shoulder straps. The final look, once donned, is impressive :)


One thing I noticed is that the ab and kidney plate likes to separate near the bottom, due to the slight gut I have. I guess I'll need to work out and wear a girdle in the mean time. It's the only place on my body that's overly fatty.


Additionally, the modified ANOVOS belt seems to be working well enough. The only thing left to do with it is to remove or cover up the upper two Chicago screws to qualify for Stunt Basic or EIB certification for the 501st. I plan to do this with small circular pieces of iron-on canvas patch, after I try adding some washers to the screws to reduce the chances of the holster tearing through the belt.

After the fitting, I finished trimming and gluing the painted ab buttons in place.


There were some places on the armor that had obvious rub, like the back plate into my shoulders and the posterior plate into my inner legs. So I sanded these down with the Dremel sanding drum to eliminate and taper inner edges.



I also noticed, as I did on my friend's armor during the armor party, that the posterior plate likes to stick out. To combat this, I added to two tabs on the inside of the piece, on the edge returns, so that the plate would hook behind the kidney plate when strapped into place.


I'd honestly be about done at this point, but after fitting the thighs some more, it occurred to me that, although I have the thighs properly trimmed for length, I don't have them trimmed for shape. However, more importantly, they don't come up as far as I need them to (when I'm standing). They're too tight, especially near the top where almost no material was trimmed (save the front edge returns). Therefore, I'll have to accept the fact that I need to shim them. I've already started this process, but will make another blog post dedicated entirely to the process. Until then...