This post is going to be "photo lite" as not a ton happened the session.
I unclamped the shins and found them to be good, although I'm worried about the right shin not settling into a closing position - I don't think the H&L will be able to pull it together. I'm going to ask around to see what can be done about it, weather I need to apply heat, use a different kind of closure, etc.
EDIT: read this post before working on your shins. A small number of kits were affected by mis-numbering of parts.
Until then, I installed the sniper knee on my left shin piece. I went by UKSrath's playbook on this one. although I had to trim off a small part of the overhang on the "stage left" side of the knee pad so that it wouldn't go over the bend on the knee. After quadruple-checking placement and penciling the contact points on the shin pieces, I sanded the contact points on shin and pad, cemented, and clamped.
I also trimmed the front edges off the thighs. After reading so many horror stories, I expected the thighs to be tough. After reading UKSWrath's write-up, though, they just seem to be just like the shins or forearms, just bigger.
The easiest way to trim the excess off the front, for me, is to use a strip to see where you want the edge to fall. Then, make three tiny marks for top, center, and bottom on those edges. With these in place, you can measure 10mm towards the edge of the piece (using clamps to help), line up the straight edge, draw the cutting line, and then cut using the score method or Dremel (moving clamps along the line to complete the cut as needed).
With the four front edges cut, I'll now have to worry about fitting and cutting. Fortunately, I've already measured my thighs and have a good idea as to how big these pieces will need to be for a snug yet comfortable fit. However, I may take a break tomorrow so I can catch up on chores, sleep, and hanging out with my dear wife.When it comes time to start fitting torso pieces, I'll probably need her expert Theater and costuming help to help my line them up for proper strap fitting :)
A detailed history of my rookie build of my ANOVOS Star Wars A New Hope Stormtrooper Armor kit, from basic to upgrades, including mistakes that were made along the way.
Click on any images in the blog to view at a larger resolution (if available).
Featured Post
The TKTalkie v4 - Press 6 for the Imperial March
Upgrading - the Path from v3.15 to v4.0 (Note: I had started this draft last year but never finished it, due to personal issues and cuttin...
Tuesday, February 16, 2016
Monday, February 15, 2016
Shin-anigans
Starting with the helmet again, this time it seems that the adhesive worked. I picked off the excess and got the mount back into my helmet. I removed the white interior straps and re-positioned them so that the side straps were slightly diagonal going towards rear as they got deeper into the mask, ant the top strap was re-positioned slightly towards rear. With this configuration I had enough room to easily see through the eye with my glasses on.
The one thing that's apparent is that I'll probably need to cave and buy a small fan for the mask as it gets steamy, even with the slots in the frown. But I have a Fry's near my office and an Amazon Prime account, so I'll worry about that later.
EDIT: read this post before working on your shins. A small number of kits were affected by mis-numbering of parts.
Moving back to the shins, I un-clamped the pieces and commenced to cement the outer shells to the front strip. Since the back of these shells will be fastened with H&L tape, this will be untouched for now, and certainly NOT cemented.
I have yet to address the thighs. I'll be doing some reading on uskwrath's thread to see the best method for sizing, trimming, and cementing before I tackle these. Plus, I would be able to clamp anything tonight with the shins setting up, so I instead trimmed out the sniper knee plate (#23) for the left shin and the small ammo belt (#26) for the right thigh.
I also decided to finally start trimming torso pieces, starting with the chest (#2) and back plate (#5). I had some very minor blade slip on some of the curves, but nothing that can't be polished out. Since I wanted to start piecing the upper torso together, I'll need these pieces and the shoulder straps to start.
Scraped some skin on my thumb using the score & snap method while I was snapping. Thankfully, CA glue instantly bonds to skin and makes a great makeshift band-aid to keep me from bleeding on the armor.
Going to try tackling the thigh pieces tomorrow as I finish up the shins and start working on strapping the upper torso. Going to need to order rivet pliers from Amazon for parts on the lower torso that require snaps, and perhaps for trying future harnessing methods (of course, I'll be suing the Anovos straps initially).
More fun next session :)
The one thing that's apparent is that I'll probably need to cave and buy a small fan for the mask as it gets steamy, even with the slots in the frown. But I have a Fry's near my office and an Amazon Prime account, so I'll worry about that later.
EDIT: read this post before working on your shins. A small number of kits were affected by mis-numbering of parts.
Moving back to the shins, I un-clamped the pieces and commenced to cement the outer shells to the front strip. Since the back of these shells will be fastened with H&L tape, this will be untouched for now, and certainly NOT cemented.
I have yet to address the thighs. I'll be doing some reading on uskwrath's thread to see the best method for sizing, trimming, and cementing before I tackle these. Plus, I would be able to clamp anything tonight with the shins setting up, so I instead trimmed out the sniper knee plate (#23) for the left shin and the small ammo belt (#26) for the right thigh.
I also decided to finally start trimming torso pieces, starting with the chest (#2) and back plate (#5). I had some very minor blade slip on some of the curves, but nothing that can't be polished out. Since I wanted to start piecing the upper torso together, I'll need these pieces and the shoulder straps to start.
Scraped some skin on my thumb using the score & snap method while I was snapping. Thankfully, CA glue instantly bonds to skin and makes a great makeshift band-aid to keep me from bleeding on the armor.
Going to try tackling the thigh pieces tomorrow as I finish up the shins and start working on strapping the upper torso. Going to need to order rivet pliers from Amazon for parts on the lower torso that require snaps, and perhaps for trying future harnessing methods (of course, I'll be suing the Anovos straps initially).
More fun next session :)
Sunday, February 14, 2016
The Shin-dig
Before I get to then shins, I'll talk about the stock head harness. The adhesive on the H&L strips I tried to glue didn't allow the E6000 to set up properly, so I had a big mess to clean up. After trying rubbbing alchohol, I resorted to one of the best solvents - good 'ole WD40. With some of that and some elbow grease, I was able to get most of the bad E6000 and adhesive off the back of the H&L strips and the harness itself.
Once they were cleaned, I washed them in soapy water to remove as much of the solvent as possible. I also lightly sanded the part of the harness where the H&L strips would go for better adhesion. Then I dried and dusted them off. I then tried a different adhesive, E6000's close cousin, Shoe Goo, for its strength and flexibility. Back in the clamps it went.
EDIT: read this post before working on your shins. A small number of kits were affected by mis-numbering of parts.
Next were the shins, which I had measured the previous night. After final measuring and initial cutting and re-fitting, I decided each piece needed to measure 6" at the bottom and 8" at the top for a proper fit for my shins and calves.
Once final cutting and edge sanding was done, I started gluing on the strips to the outside shells, Pieces 24 and 27, as these pieces will have both strips glued down, whereas the inside shells will not. The front Strips C were easy enough - I put a line done the center lengthwise after sanding, beveled the corners, applied E6000 to the shell, and clamped them in place using the mini clamps.
Strips D are actually wider by 5mm, but this is to provide extra spacce for the white H&L strips that make up the closures for the rear calves. For these strips, after sanding, I measured 10mm, but left the remaining 15mm for the H&L strips.
I then glued the 10mm edge to the outside shells in a fashion similar to the other strips. (I also added magnets after taking the picture to increase clamping action.)
And after exhaustive measuring, re-measuring, cutting, re-cutting, clamping, and gluing (and celebrating Valentine's Day with my wife who encouraged me to buy this kit!), that was it for the night. I'll wait for these pieces to set up before doing more work next session
Once they were cleaned, I washed them in soapy water to remove as much of the solvent as possible. I also lightly sanded the part of the harness where the H&L strips would go for better adhesion. Then I dried and dusted them off. I then tried a different adhesive, E6000's close cousin, Shoe Goo, for its strength and flexibility. Back in the clamps it went.
EDIT: read this post before working on your shins. A small number of kits were affected by mis-numbering of parts.
Next were the shins, which I had measured the previous night. After final measuring and initial cutting and re-fitting, I decided each piece needed to measure 6" at the bottom and 8" at the top for a proper fit for my shins and calves.
Once final cutting and edge sanding was done, I started gluing on the strips to the outside shells, Pieces 24 and 27, as these pieces will have both strips glued down, whereas the inside shells will not. The front Strips C were easy enough - I put a line done the center lengthwise after sanding, beveled the corners, applied E6000 to the shell, and clamped them in place using the mini clamps.
Strips D are actually wider by 5mm, but this is to provide extra spacce for the white H&L strips that make up the closures for the rear calves. For these strips, after sanding, I measured 10mm, but left the remaining 15mm for the H&L strips.
I then glued the 10mm edge to the outside shells in a fashion similar to the other strips. (I also added magnets after taking the picture to increase clamping action.)
And after exhaustive measuring, re-measuring, cutting, re-cutting, clamping, and gluing (and celebrating Valentine's Day with my wife who encouraged me to buy this kit!), that was it for the night. I'll wait for these pieces to set up before doing more work next session
EPiC beer time!
Saturday, February 13, 2016
Getting My Head Into the Game; Arms Clean-Up
During the day this weekend I've started toying around with my helmet (bucket). Namely, like many Anovos owners, I'm not satisfied with the stock harness in the helmet. Some have replaced this with pads, or gone with a cheesecloth + Plastidip method. However, as I promised to some blog viewers, I'm going to work with the kit for now, at least until it's complete; thereafter, I might make post-build blogs regarding mods.
As the the sstock harness, the two problems are the hook & loop placement in the helmet that keeps the harness in place, and the hook & loop strips coming off the harness itself. For the latter, I've decided to take the nuclear option by removing the strips, applying a gerous amount of E6000 to the harness, re-placing the strips, and clamping (especially since I won't need the clamps tonight).
I'll let that set up and then start removing and re-placing the H&L inside the helmet for better placement. I need the harness as far back as possible to give my eye glasses space (if I want to troop without contact lenses), and for possible future electronics installation (like the Pyle Pro you can see in the above photo).
I unclamped, untaped and/ or removed all magnets from all the arm pieces and I'm satisfied with the results. However, given the "screen accurate" nature of the pieces, there's significant overhang on all the pieces post-fitting.
Using the Dremel cutting wheel and sanding drum, I was able to trim to pieces jutting over down to the lower pieces for a nice, even seam. I cleaned up the strips as well, using the knife, sanding drum, and very steady hand to add bevels post installation.
There's still some minor cleanup to do on the edge returns on the shoulder, elbow, and wrist edges, but otherwise these pieces are ready for final fitting once I move to installing the strapping. As promised, I'll be using the Anovos strapping for the time being when I get to that stage.
To finish up, I put the shin pieces on my legs to do initial sizing, by overlapping the pieces and marking the overlap to determine how much total material will need to be removed from both pieces in the rear.
Next session I'll determine how to split the differeence between the pices to make an even, center-most seam in the back of the pieces for strip and H&L placement for final assembly.
As the the sstock harness, the two problems are the hook & loop placement in the helmet that keeps the harness in place, and the hook & loop strips coming off the harness itself. For the latter, I've decided to take the nuclear option by removing the strips, applying a gerous amount of E6000 to the harness, re-placing the strips, and clamping (especially since I won't need the clamps tonight).
I'll let that set up and then start removing and re-placing the H&L inside the helmet for better placement. I need the harness as far back as possible to give my eye glasses space (if I want to troop without contact lenses), and for possible future electronics installation (like the Pyle Pro you can see in the above photo).
I unclamped, untaped and/ or removed all magnets from all the arm pieces and I'm satisfied with the results. However, given the "screen accurate" nature of the pieces, there's significant overhang on all the pieces post-fitting.
Using the Dremel cutting wheel and sanding drum, I was able to trim to pieces jutting over down to the lower pieces for a nice, even seam. I cleaned up the strips as well, using the knife, sanding drum, and very steady hand to add bevels post installation.
There's still some minor cleanup to do on the edge returns on the shoulder, elbow, and wrist edges, but otherwise these pieces are ready for final fitting once I move to installing the strapping. As promised, I'll be using the Anovos strapping for the time being when I get to that stage.
To finish up, I put the shin pieces on my legs to do initial sizing, by overlapping the pieces and marking the overlap to determine how much total material will need to be removed from both pieces in the rear.
Next session I'll determine how to split the differeence between the pices to make an even, center-most seam in the back of the pieces for strip and H&L placement for final assembly.
Friday, February 12, 2016
Pulling a Stunt & Pulling Out the Stops
So it occurred to me reading the 501st CRLs in conjunction with a post on the Anovos FB group that the Hero helmet is a completely diffent sculpt from teh Stunt helmets (especiallly in regards to the number of teeth in the "frown" and the general shape of it) that Anovos sold with the kit. Not that it bothers me too much, except that the helmet is Stunt-oriented and the belt is Hero-oriented. This bascially means that I'll need to remove two Chicago rivets from the belt and cover the holes, or buy a new belt. Fortunately, UKSWrath has already done the former in a good fashion, so I'll again be using his expert notes to achieve that when I get to that point. Otherwise, what I've done on the build and what I have left to do (with the belt in addition) will remain unchanged.
That being said, I got a lot done this evening. Firstly, I unclamped the right bicep and decided it was just right. After testing the left bicep one last time, I decided it too was also fine as-is, with no further trimming. I clamped the curved edge with four clmaps, and then decided to clamp the other edge with four clamps as well. I just want the piece done, done, done.
After I was done with lefty, I went back to righty and found that one of the seams was untrue and angled. So Iifted the offending seam, cleaned the old cement off the edges, re-cemented it, and used a large c-clamp, large magnets, and small spring clamps to clamp it true, as my other clamps were in use. It should hold fine until it's set.
Additionally, I was done debating about the right bicep. I lifted the offending edge, cleaned up the old cement, shaved about 3/8" off the overhanging edge, re-cemented it, and set the edge.
I used the smaller spring clamps on the edges, but since I was out of larger clamps for the middle, I resorted to smaller magnets and masking tape, which worked quite nicely to keep the butt joint against the strip.
And for my finale for the evening, I trimmed the front edges of my shin pieces using UKSWrath's notes. I found the outside of the raised edge, measured in 10cm, and cut off the remainder using the score & snap technique.
After removal, I used the strips, which I had sanded on one side and put a mark lengthwise down the center, to ensure the cut was right and that there was enough materials for proper installation of the strip, when it comes time for gluing.
Tomorrow I'll be able to start final clean-up for the arm pieces, perform fitting and trimming on the back edges, and perhaps even start gluing the strips onto the front edge of the shins. It feels like I made a lot of progress today, in terms of building and experience.
Being Too Nitpicky?
Purchased some electronics for the helmet that came recommended to me by another trooper. Used, it was less than $10, even after tax. Looking forward to testing it out and mounting it in between working on other armor parts.
Didn't get much done last night as I had other distractions, like going to a concert :)
After the concert, though, I did final sizing for my right bicep. Now I'm just hoping it's not too snug. I set the edges with the crazy bend up in the clamps first. Then, when I got up this morning, I clamped the other edges together in order to give the first edge enough set-up time to deal with the crazy curvature with the particular edge.
The left bicep might need some very slight trim, but I want to see how the right bicep fits before I do that. I want to ensure that the right bicep isn't too tight, especially when flexing my bicep. Once I get a feel for rightly, I can see what I want to do with lefty before I glue it up.
I'm still not happy with the right forearm. The edge cemented this time, but it still feels too loose. I'm tempted to take up the outside edge on the front and take of 1/4" of material to make the raised edge better match up with the strip, and to give me a slightly better fit (you can see how the edge of the armor is still right of the strip in the above photo). I really wish I had an arming suit so I could test the fit over that, but the left forearm "feels" almost perfect, so I think it will need to be done. Going to wait to wait until the forearms are done before I revisit this piece, so I can fit shins while I re-cement the piece.
Some final fitting with the arms tonight, and hopefully I can start fitting my shin pieces, after I've done some reading on UKSWrath's thread :)
Didn't get much done last night as I had other distractions, like going to a concert :)
After the concert, though, I did final sizing for my right bicep. Now I'm just hoping it's not too snug. I set the edges with the crazy bend up in the clamps first. Then, when I got up this morning, I clamped the other edges together in order to give the first edge enough set-up time to deal with the crazy curvature with the particular edge.
The left bicep might need some very slight trim, but I want to see how the right bicep fits before I do that. I want to ensure that the right bicep isn't too tight, especially when flexing my bicep. Once I get a feel for rightly, I can see what I want to do with lefty before I glue it up.
I'm still not happy with the right forearm. The edge cemented this time, but it still feels too loose. I'm tempted to take up the outside edge on the front and take of 1/4" of material to make the raised edge better match up with the strip, and to give me a slightly better fit (you can see how the edge of the armor is still right of the strip in the above photo). I really wish I had an arming suit so I could test the fit over that, but the left forearm "feels" almost perfect, so I think it will need to be done. Going to wait to wait until the forearms are done before I revisit this piece, so I can fit shins while I re-cement the piece.
Some final fitting with the arms tonight, and hopefully I can start fitting my shin pieces, after I've done some reading on UKSWrath's thread :)
Wednesday, February 10, 2016
Covering the Big Guns
When you've got to armor up these 13" pythons, brother, what Are you gonna do?
Seriously, that's all I got.
Anyhow, before I talk about the "pythons," the forearms came out great!
Well, OK, so the right forearm didn't glue so well. I was probably too conservative with the E6000.
Good thing I didn't need the big clamps for the bicep pieces yet. Pulled the loose end up, applied more E6000 (probably too much, but I can clean up the excess after), and clamped the hell out of it (sorry, forgot to take a pick, but pretty much more of the same from last session). Fool me once, shame on you...
ON TO THE BICEPS!
The forearms came out pretty uniform, so I was able to make the biceps matching and pretty symmetrical to each other during the cut & fit. Before any fitting, though, I removed the elbow-end edge returns to make it easier to slide the pieces over my elbow during donning (no pics, but pretty much the same procedure I used on the forearms - rough cut with the disc, clean up with the sanding drum and hand sanding). I left the top edge returns in for now so that the armor can find purchase on my biceps for fitting; once I start fastening everything together, I may go back and grind them out if need be. Speaking of which:
A lot of people are confused by edge returns. According to the 501st Hero and Stunt build for the TK ANH (A New Hope) standards, only the wrist edge return removal is required for higher-level certification. However, looking at screen-used armor, the arms have no edge returns on any of the ends. Typically, you'll probably see this more on the Hero suits than the Stunt suits in the actual movie. Why? Because it takes more time to remove them, so the shop probably only removed them for suits that absolutely required it (especially for comfort for actors who would be doing a lot of movement and/ or be in them for hours on end) so they could build suits for extras faster, especially given deadlines and budgets.
Therefore, if you want your suit to look and feel better, feel free to pop out edge returns in the arms, as none of them are required if you're going for 501st cert (and if you aren't, pop them out anyhow, because it makes the arms much more comfortable and less pinchy). For more info in regards to 501st cert for the ANOVOS kits, you can find the Hero cert here and the Stunt cert here. Be advised that some edge returns, especially in the body pieces, are required, so don't go hog wild until you read up.
EDIT: also, read this post for clarification between "edge returns" and "inside edges." As the arms pieces include no actual "edge returns," read the above as referring to "inside edges".
I used the same technique as the forearms - measure, tape to simulated fit, cut conservatively, and repeat until they're fit bu not too tight. This time I used the score & snap method for the cutting.
After fitting my biceps, it was time to glue the strips on - again :P This time I cut the strips to length and applied a small 45 degree bevel on the corners before gluing in place.
The fit on the biceps was slightly loose on my final test fit. I may remove a fraction of material from the outside pieces before final assembly tomorrow, after a better test fit with the strip in place - especially if it helps marry up the butt joints. While the biceps are gluing, I can start on the shins and thighs, although I may need more rare earth magnets for the latter, given the size of the pieces.
My wife and I are going to a concert tomorrow night though, so I may not get any work done. All the better I suppose, as my wife is becoming an armor widow :P
Until next time...
Edit: for reference:
Seriously, that's all I got.
Anyhow, before I talk about the "pythons," the forearms came out great!
Well, OK, so the right forearm didn't glue so well. I was probably too conservative with the E6000.
Good thing I didn't need the big clamps for the bicep pieces yet. Pulled the loose end up, applied more E6000 (probably too much, but I can clean up the excess after), and clamped the hell out of it (sorry, forgot to take a pick, but pretty much more of the same from last session). Fool me once, shame on you...
ON TO THE BICEPS!
The forearms came out pretty uniform, so I was able to make the biceps matching and pretty symmetrical to each other during the cut & fit. Before any fitting, though, I removed the elbow-end edge returns to make it easier to slide the pieces over my elbow during donning (no pics, but pretty much the same procedure I used on the forearms - rough cut with the disc, clean up with the sanding drum and hand sanding). I left the top edge returns in for now so that the armor can find purchase on my biceps for fitting; once I start fastening everything together, I may go back and grind them out if need be. Speaking of which:
A lot of people are confused by edge returns. According to the 501st Hero and Stunt build for the TK ANH (A New Hope) standards, only the wrist edge return removal is required for higher-level certification. However, looking at screen-used armor, the arms have no edge returns on any of the ends. Typically, you'll probably see this more on the Hero suits than the Stunt suits in the actual movie. Why? Because it takes more time to remove them, so the shop probably only removed them for suits that absolutely required it (especially for comfort for actors who would be doing a lot of movement and/ or be in them for hours on end) so they could build suits for extras faster, especially given deadlines and budgets.
Therefore, if you want your suit to look and feel better, feel free to pop out edge returns in the arms, as none of them are required if you're going for 501st cert (and if you aren't, pop them out anyhow, because it makes the arms much more comfortable and less pinchy). For more info in regards to 501st cert for the ANOVOS kits, you can find the Hero cert here and the Stunt cert here. Be advised that some edge returns, especially in the body pieces, are required, so don't go hog wild until you read up.
EDIT: also, read this post for clarification between "edge returns" and "inside edges." As the arms pieces include no actual "edge returns," read the above as referring to "inside edges".
I used the same technique as the forearms - measure, tape to simulated fit, cut conservatively, and repeat until they're fit bu not too tight. This time I used the score & snap method for the cutting.
After fitting my biceps, it was time to glue the strips on - again :P This time I cut the strips to length and applied a small 45 degree bevel on the corners before gluing in place.
My wife and I are going to a concert tomorrow night though, so I may not get any work done. All the better I suppose, as my wife is becoming an armor widow :P
Until next time...
Edit: for reference:
Subscribe to:
Posts (Atom)









































